4 Axis CNC Router Kit 12.0 Nm(1699.68oz.in) Nema 34 Stepper Motor & Driver & Power Supply

     0 reviews  |  Write a review
SKU: 4-DM860Y-34HE59
$460.10

Bulk quantity price break:

Qty 5 10 50 100
Price $446.56 $433.03 $419.50 $405.97
Save 3% 6% 9% 12%
Availability: 89

Qty

askquestion
This CNC kit includes:
  • 4 x Digital Stepper Driver 2.4-7.2A AC18V-80V / DC 36V-110V for Nema 34 Motor
  • 4 x E Series Nema 34 Stepper Motor Bipolar 1.8deg 12.0 Nm(1699.68oz.in) 6.0A 86x86x151.5mm 4 Wires
  • 4 x 350W 60V 5.9A 115/230V Switching Power Supply Stepper Motor CNC Router Kits

Motor Specification

  • Manufacturer Part Number: 34HE59-6004S
  • Number of phase: 2
  • Step Angle: 1.8 deg
  • Holding Torque: 12.0 Nm(1699.68oz.in)
  • Rated Current/phase: 6.0 A
  • Phase Resistance: 0.7 ohms± 10%
  • Inductance: 7.9 mH ± 20%(1KHz)
  • Frame Size: 86 x 86 mm
  • Body Length: 151.5 mm
  • Shaft Diameter: Φ14 mm
  • Shaft Length: 37 mm
  • Keyway Shaft Length: 25 mm
  • Number of Leads: 4
  • Lead Length: 500 mm

Connection

A+
A-
B+
B-
BLK
GRN
RED
BLU


Driver Specification

  • Output Peak Current: 2.4 - 7.2 A(2.0~6.0RMS)
  • Input Voltage: AC18V~80V/DC 36V-110V
  • Logic Signal Current: 7 - 15 mA (Typical 10 mA)
  • Pulse Input Frequency: 0 - 200 kHz
  • Pulse Width: 2.5μS
  • Isolation Resistance: 500 MΩ
  • Cooling: Natural Cooling or Forced cooling
  • Environment: Avoid dust, oil fog and corrosive gases
  • Ambient Temperature: 0 - 65 ℃
  • Humidity: 40% - 90% RH
  • Operating Temperature: 50 ℃ MAX
  • Vibration: 10-50Hz/0.15mm
  • Storage Temperature: -20 - 65 ℃

Power Supply Specification

  • 60V DC 5.9A output
  • AC input voltage range: 93~132V/176~264VAC
  • 115V/230V AC selected by switch
  • High efficiency low cost
  • Forced air cooling by built-in DC fan
  • Low output ripple and yawp
  • Over current, over voltage, short circuit and overheat protections
  • 215*115*50mm (L*W*H)

Resources

CNC Kit Specification
No of Axis 4 Axis
Open-loop/Closed-loop Open-loop
Motor Specification
Body Length(mm) 151.5
Holding Torque(Ncm) 1200
Holding Torque(oz.in) 1699.68
Inductance(mH) 7.9
Lead Length(mm) 500
Motor Nema Size nema 34
No. of Lead 4
Phase Resistance(ohm) 0.7
Rated Current(A) 6.0
Shaft Diameter(mm) 14
Shaft Length(mm) 37
Step Angle(°) 1.8
Stepper Driver Specification
Input Voltage(V) AC18V~80V/DC 36V-110V
Microstep(Steps/rev.) 400-40000
Max. Pulse Input(kHZ) 200
Pulse Width(μs) 2.5

Write a review

Note: HTML is not translated!
Captcha

Do you have any questions about 4 Axis CNC Router Kit 12.0 Nm(1699.68oz.in) Nema 34 Stepper Motor & Driver & Power Supply?

Captcha

SHIPS IN 24 HOURS

100% LOW PRICES GUARANTEE

CUSTOMER SUPPORT