- Your shopping cart is empty!
WELCOME TO STEPPERONLINE
3 Axis Stepper CNC Kit 3.0Nm(425oz.in) 4.2A Nema 23 Stepper Motor & Driver DM556T
3 Axis Stepper CNC Kit 3.0Nm(425oz.in) 4.2A Nema 23 Stepper Motor & Driver DM556T
SKU: 3-DM556T-23HS45
$213.97
Bulk quantity price break:
Qty | 5 | 10 | 50 | 100 |
---|---|---|---|---|
Price | $213.97 | $208.75 | $208.75 | $208.75 |
Save | 0% | 2% | 2% | 2% |
Availability: 10
askquestion
This CNC kit included:
- 3 x Digital Stepper Drive 1.8~5.6A 20-50VDC DM556T
- 3 x Nema 23 Bipolar 3Nm (425oz.in) 4.2A 57x57x114mm 4 Wires Stepper Motor CNC
- 1 x 400W 36V 11A 115/230V Switching Power Supply
Motor Specification
- Manufacturer Part Number: 23HS45-4204S
- Motor Type: Bipolar Stepper
- Step Angle: 1.8 deg
- Holding Torque: 3.0Nm(425oz.in)
- Rated Current/phase: 4.2A
- Phase Resistance: 0.9ohms
- Inductance: 3.8mH ± 20%(1KHz)
- Frame Size: 57 x 57mm
- Body Length: 113 mm
- Shaft Diameter: Φ10mm
- Shaft Length: 24mm
- D-cut Length: 20mm
- Number of Leads: 4
- Lead Length: 400mm
Connection
A+ |
A- |
B+ |
B- |
Black |
Green |
Red |
Blue |
Driver Specification
- Anti-Resonance for optimal torque, extra smooth motion, low motor heating and noise
- Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors
- Step & direction (PUL/DIR) control
- Multi-Stepping for smooth motor movement
- TTL compatible and optically isolated inputs
- Input voltage 20-50VDC
- 16 selectable micro-step resolutions of 400-25,600 via DIP switches
- 8 selectable output current settings of 1.8 - 5.6A via DIP switches
- Soft-start with no "jump" when powered on
- Pulse input frequency up to 200 KHz
- Automatic idle-current reduction
- Protections for over-voltage and over-current
Power Specification
- 36V DC 11A output
- AC input voltage range: 93~132V/176~264VAC
- 115V/230V AC selected by switch
- High efficiency low cost
- Forced air cooling by built-in DC fan
- Low output ripple and yawp
- Over current, over voltage, short circuit and overheat protections
- 215*115*50mm (L*W*H)
Resources
- Motor Datasheet: 23HS45-4204S.pdf
- Motor Torque Curve: 23HS45-4204S_Torque_Curve.pdf
- Driver Manual: DM556T.pdf
- Power Supply Manual: S-400-36.pdf
CNC Kit Specification | |
No of Axis | Single Axis |
Open-loop/Closed-loop | Open-loop |
Motor Specification | |
Body Length(mm) | 113 |
Holding Torque(Ncm) | 300 |
Holding Torque(oz.in) | 425 |
Inductance(mH) | 3.8 |
Lead Length(mm) | 400 |
Motor Nema Size | Nema 23 |
No. of Lead | 4 |
Phase Resistance(ohm) | 0.9 |
Rated Current(A) | 4.2 |
Shaft Diameter(mm) | 10 |
Shaft Length(mm) | 24 |
Step Angle(°) | 1.8 |
Stepper Driver Specification | |
Input Voltage(V) | 20 - 50 |
Output Current(A) | 1.8 - 5.6 |
Microstep(Steps/rev.) | 400 - 25600 |
Max. Pulse Input(kHZ) | 200 |
Pulse Width(μs) | 2.5 |